Menu
Locate and manage all your devices in one place.

Navis - Señal CH - 4713

 
Start Your FreeMonth
       
From $0.99 USD*Month/Device
       
Pay as you go. No contract
Señal CH - 4713
Visit the manufacturer website
Tracker Car Navis CH-4713 GLONASS

Navis CH-4713 board GLONASS navigation-connected terminal operating signals GLONASS, GPS, SBAS-enabled mode A-GNSS, to monitor the location, condition, and the route of the vehicle in real time.

On-board navigation and communication terminal operating signals GLONASS, GPS, SBAS-enabled mode A-GNSS, to monitor the location, condition, and the route of the vehicle in real time.

CH-4713 - navigation and communications equipment, installed on the vehicle to enable the transmission of navigation and telemetry information about the operation of the vehicle and airborne equipment for mobile radio networks, as well as to allow for the exchange of voice messages to the monitoring center.

Support modes «Assisted GNSS» 
Protection against unauthorized disconnection of connectors and antennas 
Configuration over the air 
Built-in navigation device with a display in the cab 
Advanced configuration algorithm works 
The ability of the blocking action on the vehicle units 
Possibility of covert listening booths 
System optimization of the length of the transmitted message 
The system of protection against short-circuit and antenna input / output 
Built-driver identification (iButton) 
Programmable security functions 
Features and Benefits:

Terminal CH-4713 is based on the receiver CH-4706, which has a high sensitivity and provides accurate and stable determination of coordinates in a weak and multipath.

Terminal CH-4713 provides the following tasks:

The reception of navigation signals and data on geographic coordinates, speed and direction of travel of the vehicle 
The definition and transmission of information on the state of the vehicle, on the work of the special systems and equipment on the basis of information received by CAN-bus, and reading of digital and analog sensors 
Communication between the monitoring center and connected to the terminal devices with a serial interface 
Providing voice communication operators with the driver of the vehicle 
Connect button "Alarm" 
Storing data on the movement and condition of the vehicle in violation of the communication channel and automatic transmission of stored information to the server when communication is restored 
Management of the onboard equipment of the vehicle via the digital interface and outputs 
Security vehicle 
Specifications:

The number of receiving channels of GLONASS / GPS / SBAS 24
Mode All-in-view
GLONASS L1, (1592-1610 MHz)

 ST - code
GPS / SBAS
 L1 (1575.42 MHz)
C / A-code
 
The accuracy of determining navigation data:
 
Coordinates in the plane: 
 
- Offline 5 m (typically 3 m)
- In the diff. Mode 2 m
 
8 m high (typically 5 m)
 
Velocity of 0.1 m / s
 
Time of receipt of navigation parameters:
 
"Cold start" 50
"Warm start" 20
"Recapture" 3
 
Admission and registration correction information in accordance with the recommendations of RTCM
The sensitivity of -163 dB / W
Restrictions on the movement parameters of the object:
 
ground speed from 0 to 500 m / s
acceleration up to 5g
height of 18 000m

Performance:

The supply voltage range of 6.8 to 48V
 
Playtime on internal battery (Li-ion)> 2:00
Power consumption <3W
Operating temperature range from -30 to + 65 ° C
Relative humidity Up to 95%
Protection class IP51
Dimensions 200 x 90 x 43mm
Housing material Aluminium
Interface: Data network GSM 850/900/1800/1900
GPRS, SMS
Communication protocol TCP / IP
Capacity non-volatile memory of events up to 20 000 records
Number of digital inputs 10
Number of analog inputs and 6
The total number of inputs 12
Number of digital outputs 2

This information only is for informational purposes only, Plaspy does not have relationship with the device's manufacturer, for more information check the manufacturer's website or user manual.

Use Plaspy with a tracker

  • Set the Operator APN
    Country Operator APN User Password
  • Check your tracker clock setup is set UTC-0 o GMT. (The most trackers come from the factory on UTC.)
  • For most devices you should use IMEI (International Mobile Equipment Identity) number as unique identifier. However, some devices have vendor specific unique identifier, for example TK-103 devices use 11-digit identifier.
  • Set Up the Plaspy's IP and port on your tracker: (Plaspy detects tracker's protocol.)
    Server IP Port
    d.plaspy.com 54.85.159.138 8888
  • Add a Plaspy Account on devices with the IMEI or unique ID.