Loading...

SinoTrack - AL-900G

Specification

Operating temperature -15°C ~ 80°C
Storage temperature -20°C ~ 85°C
Operating humidity 0% ~ 90% ((Non-water vapor condensing))
Protection degree IP53
Power voltage 9V ~ 40V
Input current 80mA ~ 2000mA
Power rating 1.5W
Operating current 60mA(GSM available), 120mA(maximum)
Back up battery 4.2V / 750mAH Lithium battery
GSM Module SimCom, Four-Band GSM850/900/1800/1900 (MHz)
GPRS connectivity GPRS multi-slot class 10, GPRS mobile station class B
GPS antenna Impedance 50 ohms
GPS Module Sirf IV, baud rate 9600bps, signal frequency1575MHz, 20 channels
GPS sensitivity Acquisition sensitivity-148dbm, receiving sensitivity -159dbm
Position accuracy 10m CEP without S/A
SIM card connector voltage 3V
MCU ATMel
acquisition Hot start 1s, warm start 38s,cold start 42s
Indicator LED 3colors indicator: Red(power),Yellow(GPS),Green(GSM)

 

Hardware Features

Positioning 24-hour satellite positioning:
  1. SMS location racking
  2. signal real time location tracking
  3. GPRS location tracking via time interval
Authorized wiretapping The vehicle can be wiretapped as authorized(inside microphone):
  1. SMS set authorized TEL number.
  2. Platform send command to listen.
Alarm
  1. over-speed alarm.
  2. SOS.
  3. Main power on/off alarm
Input
  1. ACC.
  2. Door sensor.
  3. Shock sensor.
  4. fuel sensor.
Output
  1. remotely control fuel (with relay).
  2. remotely control electricity (with relay).
Parameters setting
  1. set tracker SMS password.
  2. set SOS and wiretapping TEL number.
  3. set over-speed value.
  4. set position report time interval.
  5. set GPRS position report mode
    1. fixed time running interval(when vehicle’s running).
    2. Report when car turning.
    3. Static interval (when vehicle’s parking, the time interval is 60times than running interval, this mode could save GPRS traffic and doesn’t affect vehicle alarms. If alarm happens, tracker will report position to platform).
  6. SMS or Platform(GPRS) remotely reboot tracker.
  7. SMS or Platform (GPRS) remotely set server IP, Port.
  8. Directly set parameters with LCD or dispatch handle
    1. Set APN.
    2. Set server IP, port.
Break point store When tracker is under GSM blind area, inside flash will store the location data, and then tracker will report data to platform when GSM signal is available.
Two-way communication With dispatch handle or LCD, tracker can receive and dial out any number.
SMS Dispatch With LCD or dispatch handl:
  1. user can send text messages to LCD or handle from platform.
Take Photo Tracker can connect two cameras and multi-mode to take photo:
  1. Press SOS to take photo.
  2. Open/close door to take photo.
  3. Take photo by fixed time interval.
  4. Take photo via platform command.
RFID Tracker can connect RFID card reader:
  1. Driver card identification.
  2. Driver registration managemen.
  3. Start device after RFID.
Fatigue driving Driver drives continuously over 4hours, and take rest less than 15minutes, tracker will send alarm.
PC data cable Connect to PC USB
  1. Set server IP, port, APN.
  2. Set tracker interval, over-speed, photo taking interval, alarm SMS notice, etc.
  3. Set car license plate number, car owner, Vehicle identification number (VIN), etc.
  4. Read driving record data and various reports stored in SD card.
SD card Store all location data, similar as driving recorder.
  1. 4G Micro SD card, it could store driving data around 10years(say interval is 10s).
  2. The record data includes: time, speed, direction, longitude and latitude, door status, engine status, fuel consumption, temperature, mileage, SOS, over-speed, GPS signal, GSM signal, etc.
Printer Printer directly connects to tracker and print directly, no need based on server:
  1. Print vehicle data: vehicle owner, company, company address, Vehicle identification number.
  2. Print last RFID card’s driver data: driver name, RFID car number, card time, driving license number, driving license issue date, RFID card issue date, RFID card expire date.
  3. Print last RFID card and driver’s continuously driving time.
  4. Print all 10 position data from any time around.
  5. Print over-speed times after RFID user swipe card.
  6. Print door open/close times after RFID user swipe card.
  7. Print engine on/off times after RFID user swipe card.
  8. Print fatigue driving after RFID user swipe card.
  9. Print RFID user card after RFID user swipe card.
  10. Can timing print.

 

This information only is for informational purposes only, Plaspy does not have relationship with the device's manufacturer, for more information check the manufacturer's website or user manual.

Set Up AL-900G

Country
Carrier
APN
User
Password

The Sinotrack trackers work in 6Pzp0Q with the ID found in the MoFgN command, to configure the tracker send the following commands via text messages

  1. Restore factory settings
    RESET
  2. Set the time zone to UTC-0
    8960000E00
  3. Set the APN of the operator
    8030000 {{apn}} {{apnu}} {{apnp}}
  4. Set up the GPRS server
    8040000 54.85.159.138 8888
  5. Set update interval on
    8050000 60
  6. Set update interval off
    8090000 60
  7. Switch to GPRS mode
    7100000

To check the settings MoFgN