The GV600WG from Queclink is a rugged GPS tracker designed for heavy-duty vehicles — trailers, tankers, refrigerated units and flatbeds — and is Plaspy compatible for fast integration into fleet management workflows. With IP67 waterproofing, tamper-resistant internal antennas and a high-capacity internal battery, the GV600WG delivers reliable real-time tracking and rich telemetry even in the most demanding transport environments.
Built around an integrated u-blox All‑in‑One GNSS receiver and broad UMTS/GSM cellular support, the GV600WG offers precise location, flexible reporting modes and extensive I/O for ignition detection, analog sensors and BLE accessories. Pairing this device with Plaspy provides a scalable solution for anti-theft protection, remote immobilizer control, fuel monitoring interfaces and end-to-end trailer lifecycle visibility.
Key Highlights
- Rugged IP67 waterproof housing and durable construction for harsh fleet environments and chemical/fuel transport.
- Exceptional standby battery life — internal 3.7V 5800 mAh (18650) pack supports up to 120 days when reporting once per day — ideal for trailers without continuous power.
- Precision GNSS positioning with u-blox receiver (autonomous accuracy < 2.5 m CEP) and high sensitivity (tracking -162 dBm) for reliable real-time tracking.
- Wide cellular coverage: UMTS/HSPA and GSM/GPRS/EDGE across global bands for consistent connectivity and telemetry upload.
- Comprehensive I/O set for fleet telemetry: ignition input, analog input (0–32 V), 1-wire temperature/iButton support, serial ports and configurable digital outputs.
- Supports BLE accessories (temperature & humidity sensors, key fobs, I/O expanders) for expanded monitoring and anti-theft workflows.
- On-device buffering of up to 10,000 messages ensures data continuity during network outages.
- Remote control capabilities (OTA control of digital outputs) enable immobilizer-style interventions and remote asset management.
How It Works with Plaspy
Integrating the GV600WG with Plaspy delivers a complete telemetry and tracking flow: the device collects GNSS and sensor data, then transmits messages to Plaspy over standard transports. Plaspy decodes incoming packets, presents real-time location on maps, triggers geo-fence and alarm workflows, and stores historical telemetry for reports and analytics. This Plaspy-compatible setup supports proactive fleet management and anti-theft response while preserving data continuity during connectivity loss.
- Real-time location and telemetry updates sent over TCP, UDP or SMS to Plaspy for live tracking dashboards and historical logs.
- Ignition state monitoring via the positive trigger input to support driver behavior reports, route start/stop events and fuel-saving strategies.
- Analog input usable for fuel monitoring or other analog telemetry, with custom thresholds and alarms in Plaspy.
- Remote immobilizer and output control via OTA digital output commands to implement anti-theft interventions from Plaspy.
- Bluetooth sensors (BLE) for temperature/humidity and key-fob presence integrated into Plaspy alerts and compliance monitoring.
- Geo-fence alarms (up to 20 circular + 20 polygon regions), low-battery alerts and accelerometer-triggered special alarms forwarded to Plaspy for instant notification.
Technical Overview
| Connectivity | UMTS/HSPA and GSM/GPRS/EDGE; HSPA DL up to 7.2 Mbps / UL up to 5.76 Mbps |
|---|---|
| Bands | UMTS/HSPA 850/900/1900/2100 MHz; GSM 850/900/1800/1900 MHz |
| Power & Battery | Internal lithium-ion battery 3.7V, 5800 mAh (18650); standby up to 120 days when reporting once per day; operating voltage DC 8–32 V; supports multiple power sources; 18-pin waterproof connector |
| Interfaces | 1 positive-trigger digital input (ignition detection); 1 analog input (0–32 V); 1-wire support (temperature sensors, iButton ID); 1 power output (3.3 V); 4 configurable negative-trigger inputs or open-drain outputs (150 mA max); RS232 and TTL serial ports |
| GNSS | u-blox All-in-One GNSS receiver; autonomous position accuracy < 2.5 m CEP; sensitivity tracking -162 dBm; TTFF: cold/warm ≈ 27 s, hot ≈ 1 s |
| Bluetooth | BLE support for accessories (temperature & humidity sensors, key fobs, I/O expanders) |
| Remote Management | TCP, UDP, SMS transports; OTA control of digital outputs; on-device buffer up to 10,000 messages; flexible reporting modes (time, distance, mileage) |
| Form Factor & Environmental | 135 × 62 × 38 mm, 320 g; IP67 waterproof; operating voltage DC 8–32 V; temp -30 °C to +80 °C; humidity 0%–95% non-condensing |
Use Cases
- Fleet management for trailers and heavy vehicles — continuous position, mileage and ignition telemetry for scheduling and utilization reporting.
- Anti-theft protection and remote immobilization — Plaspy-enabled alerts plus OTA output control for timely intervention.
- Refrigerated and temperature-sensitive cargo — BLE temperature sensors or 1-wire probes feed Plaspy for compliance and spoilage prevention alerts.
- Tankers and hazardous materials — IP67 housing and rugged construction for safe tracking in harsh fuel and chemical transport environments.
- Seasonal or rental trailers — long battery standby supports long-term deployments when external power is disconnected.
Why Choose This Tracker with Plaspy
Pairing the GV600WG with Plaspy gives fleet operators a rugged, Plaspy compatible GPS tracker that balances long battery life, precise GNSS positioning and a full set of fleet-focused interfaces. The device’s internal BLE support, analog input and serial ports make it straightforward to extend telemetry for fuel monitoring, temperature compliance and driver/asset ID. On the operations side, TCP/UDP/SMS transport and robust message buffering ensure continuous data in Plaspy for reliable reporting, geofencing and anti-theft workflows.
Note: Queclink has announced the phase-out (EOL) of the GV600WG with orders discontinued as of 8 August 2025. A one-year warranty is provided for affected customers, and Queclink recommends migration options such as the GV650CAU Lite. While the GV600WG remains a solid Plaspy compatible choice while available, consult Queclink or your Plaspy integrator for migration planning and long-term fleet roadmaps.
Set Up GV600WG
To set the tracker send the following commands by SMS messages, the sample setup the device password is c6XOig47, this password is the default
- Restore factory settings
AT+GTRTO=c6XOig47,4,,,,,,FFFF$ - Set the time zone UTC-0
AT+GTTMA=c6XOig47,+,0,0,0,,,,,,FFFF$ - Set the operator APN
AT+GTBSI=c6XOig47,{{apn}},{{apnu}},{{apnp}},,,,,FFFF$ - Set the GPRS server
AT+GTSRI=c6XOig47,4,,1,d.plaspy.com,8888,54.85.159.138,8888,,0,0,0,,,,FFFF$ - Set the update interval 60 seconds.
AT+GTFRI=c6XOig47,1,1,0,0,,,60,60,60,60,7F,40,0,,,FFFF$ - Enable SOS button notification input 2
AT+GTSOS=c6XOig47,2,2,,0,0,0,0,0,0,,,FFFF$
